Team:Dalton School NY/Notebook

From 2012hs.igem.org

Revision as of 12:54, 1 June 2012 by Jhackett (Talk | contribs)

In progress...

Contents

Testing of DNA prepared by several methods

Yeast genomic DNA is commonly prepared using a phenol/chloroform based method. Because both phenol and chloroform are toxic chemicals, we tested several methods for preparing yeast genomic DNA that do not use these chemicals. We compared a method that uses LiOAc to disrupt the yeast cell wall (BioTechniques 50:325-328, 2011) to methods that use the enzyme zymolyase to disrupt the cell wall (a Promega kit or a protocol from Jim Haber’s lab, “JH zym”). The Haber lab protocol produced the greatest yield of genomic DNA, but DNA made using the Promega kit was used in subsequent PCRs because it seemed to produce the most consistent results. 1µl, 2µl, or 5µl of genomic DNA was used in each PCR reaction with LIF1 promoter primers. Following these initial tests, 1µl of yeast genomic DNA was used for subsequent PCRs. The LiOAc method was the shortest and least expensive and we may switch to this method when future DNA preps are needed.


Dalton Fig7.jpg We did an isolation of genomic DNA from yeast using the Promega Wizard Genomic DNA Purification Kit- cat# A1120. We substituted 20T zymolyase (Seikagaku) for lyticase.

PCR of promoters and fluorescent protein coding sequences

For PCR, we used: Yeast Genomic DNA: 1µl

2X OneTaq Mix (NEB): 25µl

5µM Forward primer: 2.5µl

5µM Reverse primer: 2.5µl

H2O: 19µl

Dalton Fig6.jpg

Then we conducted a gel extraction, using QIAquick Gel Extraction Kit.

Blunting the PCR Product

After we had the purified PCR product, we used the Blunt Cloning Kit (NEB) to blunt and phosphorylate the ends of the PCR product. The blunting reaction was composed of: Purified DNA: 15µl 10X Blunting Buffer: 2.5µl 1 mM dNTP Mix: 2.5µl Blunt Enzyme Mix: 1.0µl Sterile dH20: 4µl Total Volume: 25µl

Digestion of Puc19

Ligation

Next, we did a ligation reaction with the Quick Ligation Kit (NEB). We followed the manufacturer's suggested protocol which was to use a 3:1 molar ratio of insert: vector and 50 ng of vector.

Transformation

For the transformation, we used NEB 10-beta Competent E. coli cells (cat # C3019H). We followed the manufacturer's suggested protocol for the transformation, and we plated on Ampicillin/IPTG/X-Gal.

BsaI-digested Miniprep DNA

We then picked two colonies from each plate and inoculated 2ml of LB/amp and then mini-prepped the DNA. The samples on these gels contain BsaI-digested miniprep DNA prepared from individual colonies from the transformations above.

For the BsaI Digest, we used: Miniprep DNA: 4µl 10X NEB4: 2µl 100X BSA: .2µl BsaI: .5µl H20: 13.3µl

Dalton Fig8.jpg

Based on the data above, we concluded that the following clones had inserts of the correct size:

Promoters

MET15 yes: B

GAL1 yes: A

GAL1-L yes: A

GAL1-S yes: B

RAD52 yes: B

RAD50 yes: A

RAD54 yes: A, B

RAD55 yes: A, B

MRE11 yes: A, B

XRS2 yes: A, B

REV1 yes: B

TDH3 yes: A, B

LIF1 none

MIG1 yes: B

TUB1 yes: A

CSE4 yes: B

CLN2 yes: B

CLB2 none

ACT1 none

ENO1 none

ENO2 none

TEF2 yes: B

TEF1 none

EAF6 none (possibly a band, but too little DNA to be confident)

HSP12 yes: A, B

HSP26 yes: A

HSC82 none

MSN2 yes: A

MSN4 none

HHO1 yes: A, D


Protein-coding sequences

BFP maybe: A (the insert may be too large)

GFP none

YFP none

mTangerine none

mCherry yes: A (but bottom band seems possibly too intense)

mGrape1 none


Extra colonies were picked from the transformations for the following promoter clones:

LIF1, CLB2, ACT1, ENO1, ENO2, TEF1, EAF6, HSC82, MSN4

DNA from these clones was miniprepped using Qiagen minipreps. The DNA was digested with BsaI as follows:

miniprep DNA: 3µl

10X NEBuffer 4: 2µl

100X BSA: 0.2µl

BsaI: 0.5µl

H2O: 14.8µl

BsaI digests were incubated at 37°C for 2 hrs and then run on a 2% agarose gel in 1X sodium borate buffer.


Dalton Fig9.jpg


Based on the data above, we concluded that the following clones had inserts of the correct size:

Promoters

LIF1 none

CLB2 yes: C

ACT1 yes: C

ENO1 none

ENO2 yes: C

TEF1 none

EAF6 yes: D (This was started from culture EAF6-B)

HSC82 none

MSN4 none


Obtaining the remaining clones

Because there had been relatively few colonies on most of the transformation plates, we decided to try 2 different strategies for obtaining the remaining clones:

1. Repeat the original blunt ligations using a higher insert:vector ratio. 2. Try a sticky-end ligation strategy since it may have a higher success rate than the blunt ligation strategy. (This strategy is outlined in detail below:

When we designed the PCR primers, we added nucleotides 5' to the BSA recognition site in both the forward and reverse primers. We decided to introduce the sequence 5' CCCGGG 3'which is the site for both SmaI (creates blunt ends) and XmaI (creates sticky ends). According to the NEB catalog, SmaI and XmaI can cut very close to the end of a PCR product. Thus, the introduction served as a backup strategy if the blunt cloning was problematic. The PCR products could be cut with XmaI and ligated into XmaI-digested pUC19.

The original PCR reaction was digested with XmaI for the following promoters:

LIF1, ENO1, TEF1, HSC82, MSN4


purified PCR product: 15µl

10X NEBuffer 4: 3µl

100X BSA: 0.3µl

BsaI: 0.5µl

H2O: 11.2µl

These digested PCR products were run on the gel below:

2% agarose gel in 1X sodium borate buffer:

Dalton Fig10.jpg

These bands were excised and purified using the QiaQuick Gel Extraction Kit.


Because the cloning of the fluorescent proteins was particularly problematic, we repeated the PCR of these genes:


5ng/µl fluorescent protein vector: 2µl

2X OneTaq Mix (NEB): 25µl

5µM Forward primer: 2.5µl

5µM Reverse primer: 2.5µl

H2O: 18µl


PCR products were purified using the QiaQuick Gel Extraction Kit.


The purified PCR products were then digested with XmaI:

purified PCR product: 15µl

10X NEBuffer 4: 3µl

100X BSA: 0.3µl

BsaI: 0.5µl

H2O: 11.2µl

These digested PCR products were run on the gel below and the bands were excised and purified using the QiaQuick Gel Extraction Kit.


The pUC19 vector was digested with XmaI:

1µg/µl pUC19 (NEB): 5µl

10X NEBuffer 4: 3µl

100X BSA: 0.3µl

BsaI: 0.5µl

H2O: 11.2µl

The pUC19 vector was digested overnight at 37°C. Then, the reaction was heated at 65°C for 20min. 1µl of Calf Intestinal Phosphatase (NEB) was added to the reaction and it was incubated at 37°C for 2 hrs. This digested, dephosphorylated vector was run on the agarose gel below.

2% agarose gel in 1X sodium borate buffer:

Dalton Fig11.jpg

These bands were excised and purified using the QiaQuick Gel Extraction Kit.


Return to our main page.