Team:CIDEB-UANL Mexico/Project/Circuit

From 2012hs.igem.org

Revision as of 22:04, 16 June 2012 by JFalcon (Talk | contribs)

banner-main iGEM-logo
Team: UANL_Mty-Mexico

Team: CIDEB-UANL Mexico

Project
Circuit
<
Stand by

The first part is called Stand-by. It is in a turned on all the time and it indicates that there is no presence of Arabinose in the sample. Thus we need a constitutive promoter that is always on and in this case we have the part R0053 that corresponds to the promoter p22-cll which position in the DNA plates sent from the MIT is 1-6M. We have to observe a response to know if the promoter is always working. In this case, a reporter will be used. This reporter is a GFP protein that emits green color fluorescence. The following part is a RBS followed by a reporter. In this case, we found a biobrick, K081012 with a location in plates 3-12M, that includes a RBS, a reporter, and a terminator, all together in a vector. What we have to do is to join the constitutive promoter 1-6M with the biobricks composed of 3 parts, the 3-12M..

High Concentration

In the High concentration section, we use the pBAD promoter which works with the AraC and acts as a repressor: when there is no Arabinose it represses the DNA transcription (..?) and when Arabinose is present it keeps working the pBAD. When Arabinose enters into the bacteria it joins with the AraC and these 2 mlecules joined are the ones that will be quantified. This promoter is found in a biobrick, I0500, joined with an AraC part. This biobrick has a location 1-14N in the plates. The following part is a RBS, but it has to be compatible with the circuit. We found 3 RBS compatible and we chose the B0034 which is the most recommended of the 3 in the Registry of Standard Biological Parts (http://partsregistry.org/Main_Page) and It has a location 1-2M in the plates. In this section, Also we need a response that indicates the presence of the Arabinose in high concentration, and this response will be through the YFP reporter. This part is the E0032 with a location 1-6E. Then we need another RBS and another part that will repress the section of Low concentration because Low and High concentration work with the same promoter, as we can see in the first image of the whole circuit. The repressor will act when the response of the amount of Arabinose measured is bigger than the response of the low concentration. In this way only the part of High concentration will keep on. In this part we use a biobrick which has the 3 parts: a RBS, a repressor, and a terminator. This is the part p0152 with a location 1-10E. This is the last part of the High concentration section..

Low Concentration

The parts that compose the Low concentration section are: the promoter pBAD I0500 (1-14N) which is the same of the High concentration, the part I746352 (2-12G) which has a RBS with a phiR73 and it is joined with the p0153 (1-10G). The amount of Arabinose is measured by the pBAD and then the response is increased by the sensitivity tuner. The phiR73 (that is in the 2-12G) receives the amount measured by the pBAD and it sends the signal to the pLL wich is a promoter I746365 (2-14A) which is joined with the part p0151 (1-10C). The p0151 has a RBS and the cI that multiplies the response received and it sends it to the part I12006 (2-11J). Also it has a terminator. Then the part 2-11J is the promoter that receives the response increased from the cI. It is joined with the part K081014 (3-12O) which has a RBS, the RFP that will give the red fluorescence response and a double terminator. The promoter receives the response increased and with this final response the red color appears. In this final part is where the high concentration’s repressor acts. The part 1-10G has a repressor which turns off the stand-by section of the circuit.